View B82442A1223A000_4535857.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1) Replace the + by the code letter for the required inductance tolerance. 2) For Ni-barrier-plated terminals replace the last two digits "00" by "50".
Please read Cautions and warnings and Important notes at the end of this document.
5
03/08
SMT inductors, SIMID series SIMID 2220-A
Characteristics and ordering codes LR H 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 10000 3% 5%
^
B82442A
Tolerance J
^
Qmin 20
f L; f Q MHz 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.0796
IR mA 170 155 140 130 120 110 100 90 85 75 70 60 55 45 40 38 36 33 30 28 25
Rmax 2.72 3.36 3.92 4.64 5.60 6.80 8.00 10.4 12.0 13.6 16.0 24.0 28.0 44.0 48.0 56.0 62.4 68.0 88.0 100 120
fres,min MHz 3.9 3.6 3.2 2.9 2.6 2.4 2.2 2.0 1.8 1.5 1.4 1.3 1.2 1.1 1.0 1.0 0.9 0.8 0.7 0.6 0.5
Ordering code1)2) B82442A1224+000 B82442A1274+000 B82442A1334+000 B82442A1394+000 B82442A1474+000 B82442A1564+000 B82442A1684+000 B82442A1824+000 B82442A1105+000 B82442A1125+000 B82442A1155+000 B82442A1185+000 B82442A1225+000 B82442A1275+000 B82442A1335+000 B82442A1395+000 B82442A1475+000 B82442A1565+000 B82442A1685+000 B82442A1825+000 B82442A1106+000
10%
K
20 20 20 20 20 20 20 30 30 30 30 30 30 30 30 30 30 30 30 30
For telecommunications in blocking filter for 12- and 16-kHz counting pulses 980 1450 2600 3050 5330
^
A
8 8 6 8 6
0.016 0.016 0.012 0.016 0.012
85 70 45 45 34
15 20 43 45 66
1.8 1.4 1.1 0.9 0.8
B82442A1984A000 B82442A1145A500 B82442A1265A000 B82442A1305A500 B82442A1535A300
Closer tolerances on request. Higher currents possible at temperatures 1) Replace the + by the code letter for the required inductance tolerance. 2) For Ni-barrier-plated terminals replace the last two digits "00" by "50".
Please read Cautions and warnings and Important notes at the end of this document.
6
03/08
SMT inductors, SIMID series SIMID 2220-A
Impedance |Z| versus frequency f measured with impedance analyzer Agilent 4191A/4194A, typical values at 20 C
10 6 | Z | 10 5
IND0089-B
B82442A
Inductance L versus DC load current IDC measured with LCR meter Agilent 4275A, typical values at 20 C
10 5 H
L 10 4
IND0090-9
B82442A
B82442A 10000 H
10 4
10 3
1000 H
10 3
10 2
100 H
10 2 1 H 10 H 100 H 1000 H 10000 H 10
6
10 1
10 H
10 1
10 0
_1
1 H
10 0 5 10
10
7
10
8
Hz 10 f
9
10
10
_2
10
_1
10 0
A 10 1 I DC
Q factor versus frequency f measured with impedance analyzer Agilent 4191A/4194A, typical values at 20 C
80 B82442A
Q
IND0091-4
Current derating Iop/IR versus ambient temperature TA (rated temperature TR = 105 C)
1.2 Iop IR B82442A 1.0
IND0092-V-E
60
0.8
40
0.6
0.4
20 1 H 10 H 100 H 1000 H 10000 H 10 5 10 6 10 7 Hz 10 8 f
0.2
0 10 4
0
0
20
40
60
80 100 120
C 160 TA
7
03/08
Cautions and warnings
Please note the recommendations in our Inductors data book (latest edition) and in the data
sheets. - Particular attention should be paid to the derating curves given there. - The soldering conditions should also be observed. Temperatures quoted in relation to wave soldering refer to the pin, not the housing.
If the components are to be washed varnished it is necessary to check whether the washing
varnish agent that is used has a negative effect on the wire insulation, any plastics that are used, or on glued joints. In particular, it is possible for washing varnish agent residues to have a negative effect in the long-term on wire insulation.
The following points must be observed if the components are potted in customer applications:
- Many potting materials shrink as they harden. They therefore exert a pressure on the plastic housing or core. This pressure can have a deleterious effect on electrical properties, and in extreme cases can damage the core or plastic housing mechanically. - It is necessary to check whether the potting material used attacks or destroys the wire insulation, plastics or glue. - The effect of the potting material can change the high-frequency behaviour of the components.
Ferrites are sensitive to direct impact. This can cause the core material to flake, or lead to
breakage of the core.
Even for customer-specific products, conclusive validation of the component in the circuit can
only be carried out by the customer.
Please read Cautions and warnings and Important notes at the end of this document.
8
03/08
Important notes
The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the "General Terms of Delivery for Products and Services in the Electrical Industry" published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DSSP, MiniBlue, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. 9 03/09

SMT inductors
SIMID series, SIMID 2220-A
Series/Type: Date: B82422A March 2008
7ffARspp
(c) EPCOS AG 2008. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited.
SMT inductors, SIMID series SIMID 2220-A
Size 2220 (EIA) or 5650 (IEC) Rated inductance 1 NH to 10000 NH Rated current 25 mA to 1800 mA Construction
Upright ferrite drum core Laser-welded winding Flame-retardant molding
B82442A
Features Temperature range up to 150 C Current handling capability up to 1.8 A High inductance ratings Qualified to AEC-Q200 Suitable for lead-free reflow soldering as referenced in JEDEC J-STD 020C RoHS-compatible

Applications Filtering of supply voltages, coupling, decoupling DC/DC converters Automotive electronics Telecommunications (e.g. blocking filter for 12- and 16-kHz counting pulses) Consumer electronics Industrial electronics

Terminals
Base material CuSn6 Layer composition Cu, Ag, Sn (lead-free)1) Electro-plated
Marking
Marking on component:
Manufacturer, L value (in nH), tolerance of L value (coded), date of manufacture (YWWD) Minimum data on reel: Manufacturer, ordering code, L value, quantity, date of packing Delivery mode and packing unit
12-mm blister tape, wound on 330-mm reel Packing unit: 1500 pcs./reel
1) Ni-barrier-plated terminals on request (B82442A*50).
Please read Cautions and warnings and Important notes at the end of this document.
2
03/08
SMT inductors, SIMID series SIMID 2220-A
Dimensional drawing and layout recommendation
0.70.2 1)
B82442A
3.50.11)
B
C D
B
IND0053-6
0.15 max.
0.7 min.1)
5+0.3
A 4.5
B 2.0
A
C 4.0
D 8.0
5.6+0.3
5+0.3
Marking
1) Soldering area
IND0088-3-E
Dimensions in mm
Taping and packing Blister tape
1.750.1 5.50.1
40.1 Component 1.5+0.1 20.05
Reel
18.4 max. 130.2
_ < 7.2
120.3
_0 12.4 +1.5
_2 330 +0
621.5
IND0350-S
_ < 6.0
80.1
1.60.1 Direction of unreeling
IND0564-H-E
Dimensions in mm
Please read Cautions and warnings and Important notes at the end of this document.
3
03/08
SMT inductors, SIMID series SIMID 2220-A
Technical data and measuring conditions Rated inductance LR Q factor Qmin Rated temperature TR Rated current IR
B82442A
Measured with impedance analyzer Agilent 4294A at frequency fL, 0.1 V, 20 C Measured with impedance analyzer Agilent 4294A at frequency fQ, 20 C 105 C Maximum permissible DC with inductance decrease L/L0 10% and temperature increase of 20 K at rated temperature Measured with network analyzer Agilent 8753D, 20 C Measured at 20 C Sn95.5Ag3.8Cu0.7: (245 5) C, (5 0.3) s Wetting of soldering area 90% (based on IEC 60068-2-58) 260 C, 40 s (as referenced in JEDEC J-STD 020C) 55/150/56 (to IEC 60068-1) Mounted: -55 C ... +150 C Packaged: -25 C ... +40 C, 75% RH Approx. 0.4 g
Self-resonance frequency fres,min DC resistance Rmax Solderability (lead-free)
Resistance to soldering heat Climatic category Storage conditions Weight
Please read Cautions and warnings and Important notes at the end of this document.
4
03/08
SMT inductors, SIMID series SIMID 2220-A
Characteristics and ordering codes LR H 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 5%
^
B82442A
Tolerance 10%
^
Qmin 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10
f L; f Q MHz 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 0.796 0.796 0.796 0.796
IR mA 1800 1700 1600 1400 1300 1200 1120 1050 950 880 810 750 690 630 580 530 480 440 400 370 340 310 290 270 250 230 210 190
Rmax 0.024 0.028 0.032 0.040 0.048 0.056 0.064 0.072 0.088 0.104 0.120 0.144 0.168 0.20 0.24 0.29 0.35 0.42 0.50 0.58 0.68 0.80 0.96 1.12 1.28 1.52 1.76 2.24
fres,min MHz 95 70 55 47 42 37 34 32 29 26 24 22 19 17 16 14 13 11.5 10.5 9.5 8.5 7.8 7.0 6.4 6.0 5.4 4.8 4.4
Ordering code1)2) B82442A1102K000 B82442A1122K000 B82442A1152K000 B82442A1182K000 B82442A1222K000 B82442A1272K000 B82442A1332K000 B82442A1392K000 B82442A1472K000 B82442A1562K000 B82442A1682K000 B82442A1822K000 B82442A1103K000 B82442A1123K000 B82442A1153K000 B82442A1183K000 B82442A1223K000 B82442A1273K000 B82442A1333+000 B82442A1393+000 B82442A1473+000 B82442A1563+000 B82442A1683+000 B82442A1823+000 B82442A1104+000 B82442A1124+000 B82442A1154+000 B82442A1184+000
K
J
^
10 K 10 10 10 10 10 20 20 20 20
10%
Closer tolerances on request. Higher currents possible at temperatures

▲Up To Search▲

Price & Availability of B82442A1223A000

	To Download B82442A1223A000 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .